TOSHIBA E STUDIO450 SERIES PCL6 DRIVER

TOSHIBA E STUDIO450 SERIES PCL6 DRIVER DETAILS:

Type: Driver
File Name: toshiba_e_33552.zip
File Size: 1.1 MB
Rating:
3.35
105 (3.35)
Downloads: 72
Supported systems: ALL Windows 32x/64x
Price: Free* (*Free Registration Required)

Download Now
TOSHIBA E STUDIO450 SERIES PCL6 DRIVER



If you are looking for information on a printer model that is not listed in this document, please refer to your printer manuals, search on the manufacturer Web site, contact the manufacturer directly to determine what toshiba e studio450 series pcl6 data streams are supported on the printer, or look at the information listed for similar printer models.

TOSHIBA E STUDIO450 SERIES PCL6 DRIVER (2019)

Note: In many cases, this document will list similar printer models that support the same printer data streams. We will do what we can to help determine how best to print to your printer from your System i. Press SW1 on the toshiba e studio450 series pcl6 stitcher controller PC board. The saddle stitcher unit will stitch the sheets, and fold and deliver the stack automatically.

Then perform positive width adjustment or negative width adjustment to suit the relationship between the stitching position and the folding position. If the stitching position is below the folding position, perform positive width adjustment. If the stitching position is above the folding position, perform negative width adjustment. If the width adjustment is 0 The stitching position and the folding position match, requiring no change. If for positive toshiba e studio450 series pcl6 adjustment Set SW so that the difference resulting from subtraction of the interval from the appropriate setting in the table below is provided.

TOSHIBA E STUDIO450 SERIES PCL6 WINDOWS VISTA DRIVER

If for negative width adjustment Set SW so that the sum resulting from addition of the interval from the appropriate setting in the table below is provided. Example: If SW is currently set to -1 and the toshiba e studio450 series pcl6 is Increase the adjustment value when the sheet of paper which has exited is "A".

Decrease the adjustment value when the sheet of paper which has exited is "B". A: Toshiba e studio450 series pcl6 the upper side of the folding is longer than the lower side B: When the upper side of the folding is shorter than the lower side. Set SW on the punch controller PC board as shown below. Press SW on the punch controller PC board.

TOSHIBA E STUDIO450 SERIES PCL6 TREIBER

Sensor output is adjusted automatically when the switch is toshiba e studio450 series pcl6. Turn OFF the power. This operation registers which puncher unit is attached to the IC on the punch driver PC board so that the puncher unit can be identified by the finisher.

Toshiba Printer Drivers Download

For this reason, this operation must be performed when the punch toshiba e studio450 series pcl6 PC board has been replaced. The number of punch holes is registered to the punch controller PC board each time the switch is pressed. Perform this adjustment after replacing the Finisher control board or when the alignment position must be changed for some reason. Turn OFF the power of the equipment. Remove 1 screw and take off the board access cover. Set the SW1 on the Finisher control board as shown in the figures below.

Access cover. Turn ON the power of the equipment while [0] button and [8] button are pressed simultaneously. The alignment plate moves to the A4 or LT size toshiba e studio450 series pcl6 and stops. It stops at the position of -5 steps from the center value of the adjustment range.

TOSHIBA e-STUDIO65 Series-PCL6 - Free download and software reviews - CNET

Press the [Button1] to toshiba e studio450 series pcl6 the alignment position. Every time the [Button1] is pressed, the alignment plate shifts 1 step 0. The gap between the alignment plates becomes narrower. When the adjustment is completed, press the [Button2] on the finisher control panel to store the adjustment value in memory. When the value is stored normally, the [LED1] on the control panel will blink for a number of times that corresponds to the adjustment value set for the equipment. See the following table for the number of times the [LED1] blinks and its corresponding adjustment value.

- Find the latest drivers for your laptops, desktops

Install the board access cover. Perform this adjustment after replacing the Finisher control board or when the stapling position must be changed for some reason. The alignment plate moves to the rear or front side stapling position and stops. It stops at the position of steps from the center value of toshiba e studio450 series pcl6 adjustment range. Press [Button 1] to adjust the stapling position.

Toshiba E Studio450series Pcl6 Driver Download

Every time [Button 1] is pressed, the alignment plate shifts 4 steps 0. It moves toward the rear side.

Note: Stapling for checking the position can be done by pressing [Button 2] with sheets placed on the finishing tray. When the adjustment is completed, press [Button 2] on the finisher control panel to store the toshiba e studio450 series pcl6 value in memory without sheets on the finishing tray.Download the latest drivers for your TOSHIBA e-STUDIOSeries PCL6 to keep your Computer up-to-date. You can download and update all TOSHIBA e-STUDIOSeries PCL6 drivers for free on this page. Choose a proper version according to your system.

Related Posts